 |
 |
 |
 |
 |
 |
 |
 |
 |
|
|
|
|
|
|
 |
|
|
|
 |
 |
 |
|
 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
 
Single Membrane Configuration: (1) 2.5” x 21” Patented PVC Membrane Vessel Housings encapsulating a 2.5” x 21” HIGH REJECTION TFC Reverse Osmosis Membrane Filter that can produce up to 300 gallons of process water daily. Typical mineral removal is greater than 99%, with a concentrate recovery ratio of 1:1 (50%) on some municipal water supplies available.
Dual Pressure Pumps with 3 Chamber Diaphragm Pump Head: Increases incoming feed water pressure to 120 psi if needed for maximum Membrane performance. The Pump Head resists rust and corrosion when used with varying water conditions.
Automatic Membrane Flush: The Membrane element is rinsed daily or upon each tank filling with the full velocity of the incoming feed water for a 10 minute interval, by-passing the concentrate valve to reduce premature scaling or bio-film on the Membrane pores.
Electronic Display Total Dissolved Solids (TDS) Meter: Displays the amount of any mineral residual remaining in the high purity water after permeating through the Membrane filter or filter elements. Typical unit of measure display is in ppm (parts per million)
High Water Pressure Cut-off Switch: Prevents the system from operating when the pressurized storage tank is full of the high purity de-mineralized water.
Membrane Housing Pressure Gauge: Allows accurate monitoring of the Booster Pump operating pressure and Membrane incoming feed water operating pressure.
Coated Steel Mounting Frame: Supports the Membrane, Pump, Valves, Filters, Gauges, and Instrumentation. Manufactured from Steel for structural integrity and powder coated to resist rust and corrosion.
High Pressure Compression Fittings: Rated up to 300 psi, utilizing heavy wall Nylon with a 3-piece Nut, Flange, and O-ring.
|
 
|
Membrane Capacity
|
< = 300 gpd @ 77 F
|
|
Membrane Size
|
2.5” x 21”
|
|
Operating Pressure
|
35 psi min. 120 psi nom.
|
|
Operating Temp
|
40-90 F
|
|
PH Range
|
3-11
|
|
Motor HP
|
24/120 Volt
|
|
Turbidity/
Clarity
|
<1.0 NTU
|
|
T.D.S.
|
< = 2000 ppm
|
|
RO Module Size
|
7” D x 28” W x 33” H
|
|
1.) High Tank level Cut-off Switch: Prevents the system from operating when the atmospheric storage tank is full of the high purity de-mineralized water.
2.) Atmospheric Storage Tanks, Pressurized Storage Tanks, and Pressure Pumps in any capacity, size, or configuration.
|
- Pre-Filter 1
This 5 micron 2 1/2” x 20” filter uses Graded Density Core, Micro-Fiber technology to remove Dirt, Rocks, Sand, Sticks, Bugs, Sediment, and other medium to smaller debris from untreated water. This filter is manufactured by thermally fusing thousands of small micro fibers together. The Graded Density Core filter material becomes extremely dense in material weight from the outer perimeter to the center core providing Graduated Depth filtration and allowing more retention of Silt and Clay to be trapped in the inner core, extending the length between service intervals and cartridge replacement. Cysts, Bacteria, and Super Fine Silt, Clay, and Debris WILL NOT be removed by this filter and will be passed on to the Membrane Filter if used in a Reverse Osmosis System, which would eventually result in premature Membrane failure. This filter would normally be used for single dispensing faucets in a Bathroom, Kitchen Sink, or an Island Sink to prevent faucet screens from plugging, or, combined with other Pre-filters in a Multi-stage Reverse Osmosis system when used on Well Water, or, as a stand alone filter. This filter can be used successfully in a Multi-Stage Reverse Osmosis System as a Primary Pre-filter providing a 1 micron or lower micron Filter is used as the Secondary Pre-filter to trap the Silt, Clay, Bacteria, and Super Fine Sediments before entering the Membrane Filter.
Recommended Service Interval on Most Water Supplies: 3-6 Months
Stage 1 C -SED5MMF2520 - (Pre-Filter)
|
- Pre-Filter 2
This 5 micron 2 1/2” x 20” filter uses Graded Density Core, Micro-Fiber technology to remove Dirt, Rocks, Sand, Sticks, Bugs, Sediment, and other medium to smaller debris from untreated water. This filter is manufactured by thermally fusing thousands of small micro fibers together. The Graded Density Core filter material becomes extremely dense in material weight from the outer perimeter to the center core providing Graduated Depth filtration and allowing more retention of Silt and Clay to be trapped in the inner core, extending the length between service intervals and cartridge replacement. Cysts, Bacteria, and Super Fine Silt, Clay, and Debris WILL NOT be removed by this filter and will be passed on to the Membrane Filter if used in a Reverse Osmosis System, which would eventually result in premature Membrane failure. This filter would normally be used for single dispensing faucets in a Bathroom, Kitchen Sink, or an Island Sink to prevent faucet screens from plugging, or, combined with other Pre-filters in a Multi-stage Reverse Osmosis system when used on Well Water, or, as a stand alone filter. This filter can be used successfully in a Multi-Stage Reverse Osmosis System as a Primary Pre-filter providing a 1 micron or lower micron Filter is used as the Secondary Pre-filter to trap the Silt, Clay, Bacteria, and Super Fine Sediments before entering the Membrane Filter.
Recommended Service Interval on Most Water Supplies: 3-6 Months
Stage 2 - CSED1MMF2520 - (Pre-Filter)
|
- Pre-Filter 3
This 5 micron 2 1/2” x 20” filter uses Graded Density Core, Micro-Fiber technology to remove Dirt, Rocks, Sand, Sticks, Bugs, Sediment, and other medium to smaller debris from untreated water. This filter is manufactured by thermally fusing thousands of small micro fibers together. The Graded Density Core filter material becomes extremely dense in material weight from the outer perimeter to the center core providing Graduated Depth filtration and allowing more retention of Silt and Clay to be trapped in the inner core, extending the length between service intervals and cartridge replacement. Cysts, Bacteria, and Super Fine Silt, Clay, and Debris WILL NOT be removed by this filter and will be passed on to the Membrane Filter if used in a Reverse Osmosis System, which would eventually result in premature Membrane failure. This filter would normally be used for single dispensing faucets in a Bathroom, Kitchen Sink, or an Island Sink to prevent faucet screens from plugging, or, combined with other Pre-filters in a Multi-stage Reverse Osmosis system when used on Well Water, or, as a stand alone filter. This filter can be used successfully in a Multi-Stage Reverse Osmosis System as a Primary Pre-filter providing a 1 micron or lower micron Filter is used as the Secondary Pre-filter to trap the Silt, Clay, Bacteria, and Super Fine Sediments before entering the Membrane Filter.
Recommended Service Interval on Most Water Supplies: 3-6 Months
Stage 3 - CCF5MCB2520 - (Pre-Filter)
|
- Membrane
This 5 micron 2 1/2” x 20” filter uses Graded Density Core, Micro-Fiber technology to remove Dirt, Rocks, Sand, Sticks, Bugs, Sediment, and other medium to smaller debris from untreated water. This filter is manufactured by thermally fusing thousands of small micro fibers together. The Graded Density Core filter material becomes extremely dense in material weight from the outer perimeter to the center core providing Graduated Depth filtration and allowing more retention of Silt and Clay to be trapped in the inner core, extending the length between service intervals and cartridge replacement. Cysts, Bacteria, and Super Fine Silt, Clay, and Debris WILL NOT be removed by this filter and will be passed on to the Membrane Filter if used in a Reverse Osmosis System, which would eventually result in premature Membrane failure. This filter would normally be used for single dispensing faucets in a Bathroom, Kitchen Sink, or an Island Sink to prevent faucet screens from plugging, or, combined with other Pre-filters in a Multi-stage Reverse Osmosis system when used on Well Water, or, as a stand alone filter. This filter can be used successfully in a Multi-Stage Reverse Osmosis System as a Primary Pre-filter providing a 1 micron or lower micron Filter is used as the Secondary Pre-filter to trap the Silt, Clay, Bacteria, and Super Fine Sediments before entering the Membrane Filter.
Recommended Service Interval on Most Water Supplies: 3-6 Months
Stage 4 - CMEM2521TFC - (Membrane Filter)
|
|
TYPICAL APPLICATION: Pre-Filter Water Treatment (R.O. Boost)
PUMP DESIGN: 3 Chamber Diaphragm Pump, Self Priming, Capable of Being Run Dry
FLOW RANGE: Open Flow = 1.40-1.95 LPM (At 80 PSI = .80-1.00 LPM)
CONSTRUCTION MATERIALS: Housings: Nylon Valves: EPDM Diaphragm: Santoprene Fasteners: Stainless Steel
MOTOR: Type: 24 VAC, Permanent Magnet, Totally Enclosed, Non-Ventilated. Power Leads: 20 AWG, 6" LONG
TEMPERATURE LIMITS: This Motor is Not Equipped with Thermal Protection. For User Safety, Optimal Performance, and Maximum Motor Life, The Motor Surface Temperature Should Not Exceed 150°F (66°C)
LIQUID TEMPERATURE: 170°F (77°C) Max.
POWER: Pumps operate safely with low energy (24 watts), low voltage (12-24V) motors. They can be used with compatible transformers offered in the most popular worldwide voltages: 100 VAC, 120 VAC, 230 VAC (transformer not included).
FITTINGS: Built-in 3/8” John Guest half-cartridge fittings eliminate the need for external fittings (unless elbow fittings are required). Note that the location and positioning of these pumps may affect their performance.
PUMP CERTIFICATIONS: NSF Standard 58
WEIGHT: 7 lbs.
 |
|
|
|
