This 1 micron filter is designed to offer the consumer 2 stages of filtration in a single, compact, cartridge element, using Graded Density Core, Carbon Impregnated Micro-Fiber Technology to reduce or remove Dirt, Iron, Sand, Sediment, Silt, Clay, Cysts, Bacteria, Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and other fine debris from untreated water. Similar to the DPF1/2MIMFPG Filter, this 1 micron filter provides an extremely high density volume weight of filter material by thermally fusing thousands of small micro fibers together, and then impregnating each fiber with Coconut Shell Carbon Powder creating a Modified Carbon Block Filter. The Graded Density Core filter material becomes extremely dense in material weight from the outer perimeter to the center core providing Graduated Depth filtration and allowing more retention of Silt and Clay to be trapped in the inner core, extending the length between service intervals and cartridge replacement. This also assures better reduction or removal of Cysts, Bacteria, super fine Silt and Clay in the 1 micron size by reducing the water flow or “Permeation” through the Modified Block. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering almost twice as many cell sites than Bituminous Coal due to the smaller size. The higher quantity of smaller cell sites in Coconut Shell Carbon can react quicker to adsorbing the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water, and retain these gases for longer periods of time than Bituminous Coal is capable of. This filter would normally be used as the PRIMARY Pre-filter to reduce or remove Sediment and Chlorine from the incoming water when combined with other pre-filters in a Multi-stage Reverse Osmosis system, or as a stand alone filter at a single dispensing faucet. This filter offers excellent protection against Fine  Sediments, Chlorine, Hydro-Carbon Gases, Cysts, Bacteria and other contaminants.

Recommended Service Interval on Most Water Supplies: 1 Year

DPF1MIMPS - Sediment/Carbon Pre-Filter #1

This (1/2) .5 micron filter is designed to offer the consumer 2 stages of filtration in a single, compact, cartridge element, using Graded Density Core, Carbon Impregnated Micro-Fiber Technology to reduce or remove Dirt, Iron, Sand, Sediment, Silt, Clay, Cysts, Bacteria, Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and other fine debris from untreated water. This 1/2 micron filter provides an extremely high density volume weight of filter material by thermally fusing thousands of small micro fibers together, and then impregnating each fiber with Coconut Shell Carbon Powder creating a Modified Carbon Block Filter. The Graded Density Core filter material becomes extremely dense in material weight from the outer perimeter to the center core providing Graduated Depth filtration and allowing more retention of Silt and Clay to be trapped in the inner core, extending the length between service intervals and cartridge replacement. This also assures better reduction or removal of Cysts, Bacteria, super fine Silt and Clay in the 1/2 micron size by reducing the water flow or “Permeation” through the Modified Block. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering almost twice as many cell sites than Bituminous Coal due to the smaller size. The higher quantity of smaller cell sites in Coconut Shell Carbon can react quicker to adsorbing the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water, and retain these gases for longer periods of time than Bituminous Coal is capable of. This filter would normally be used as the PRIMARY Pre-filter to reduce or remove Sediment and Chlorine from the incoming water in a 3-Stage Reverse Osmosis system, or when combined with other pre-filters in a Multi-stage Reverse Osmosis system, or as a stand alone filter at a single dispensing faucet. This filter offers the BEST protection against Fine  Sediments, Chlorine, Hydro-Carbon Gases, Cysts, Bacteria and other contaminants.

Recommended Service Interval on Most Water Supplies: 1 Year

DPF1/2MIMPS - Sediment/Carbon Pre-Filter #2

This .001 micron Membrane filter uses a Thin Film Composite Cellular Skin to separate and remove Dissolved Solids, Salts, Minerals, Heavy Metals, Organic Matter, Pyroxene’s, Sub-micron Colloidal matter, Cysts, Bacteria, and other contaminants from untreated water. Water containing Dissolved Minerals and other Contaminants is forced under high pressure through a Semi-Permeable, Spiral Wound, Thin Film Composite Cellular Skin layered in several wrappings, to separate and rinse away the dissolved solids to a sewage drain, leaving only the Pure, H20 water molecules for consumption, production, processing, or manufacturing. The TFC Membrane skin has a broader PH tolerance than the CTA Membrane skin, it can remove a higher maximum threshold of dissolved solids, and removes a higher percentage of dissolved solids than the CTA Membrane is capable of removing. The TFC Membrane can be used on Municipal or Well Water with proper pre-filtration due the natural Bacteriostatic properties. Typical Rejection of minerals and impurities for the TFC Membrane is 95%-99% removal, compared to 70%-80% for the CTA Membrane. TFC Membranes are used in Vending machines and Bottled Water processing plants across the U.S.A. This is the best Membrane choice available for producing the highest purity water from a Residential Reverse Osmosis System.

Recommended Service Interval on Most Water Supplies: 1 Year

MEM12TFCPS - Membrane Filter > 12-150 gpd Membranes Available: MEM24TFCPS (24gpd), MEM36TFCPS (36 gpd), MEM50TFCPS (50 gpd), MEM75TFCPS (75 gpd)

This (½) .5 micron filter uses Solid Pressed Molded Carbon Block Technology to reduce or remove Cysts, Bacteria, Fungus, Algae, Chlorine, Ammonia, Chloramines, Hydro-Carbon  Gases, and VOC’s (Volatile Organic Chemicals) from untreated water. Small granules of Coconut Shell Carbon are Crushed, Pressed and Bonded together with a “PATENTED” heat molding process to form a solid BLOCK or Brick of Carbon. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering almost twice as many cell sites than Bituminous Coal due to the smaller size. The higher quantity of smaller cell sites in Coconut Shell Carbon can react quicker to adsorbing the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water, and retain these gases for longer periods of time than Bituminous Coal is capable of. The (½) .5-micron Carbon Block Density assures better removal of contaminants by reducing the water flow or “Permeation” through the Block, and, minimizes water channeling associated with other Carbon filters. The solid Carbon Block provides 2 to 10 times more volume weight of filter material compared to other Granular Carbon, Block, and Fiber type filters by greatly reducing the porosity of the loose granules of Carbon, and void areas between fibers. This filter has also been known to be effective in reducing or removing Petroleum By-products such as MTBE, Toluene, Benzene, etc., and also Cysts and Bacteria such as Cryptosporidium, Cyclospora, Giardia, E-Coli, and Legionnaires Disease. This filter would normally be used as a post-filter for a Reverse Osmosis system, or combined with other pre-filters in a Multi-stage Reverse Osmosis system, or as a stand alone filter. Other Carbon require more frequent service intervals and cartridge replacement. This filter offers the BEST protection against Fine  Sediments, Chlorine, Hydro-Carbon Gases, VOC’s, Cysts, Bacteria and other contaminants.

Recommended Service Interval on Most Water Supplies: 1 Year

CF1/2MCBPS - Carbon Post-Filter

DPF1/2MIMFPS - Sediment/Carbon Pre-Filter

This 1/2 micron filter uses Solid Pressed Molded Carbon Block Technology to reduce or remove Cysts, Bacteria, Fungus, Algae, Chlorine, Ammonia, Chloramines, Hydro-Carbon  Gases, and VOC’s (Volatile Organic Chemicals) from untreated water. Small granules of Coconut Shell Carbon are Crushed, Pressed and Bonded together with a “PATENTED” heat molding process to form a solid BLOCK or Brick of Carbon that is encapsulated inside a plastic vessel housing. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering almost twice as many cell sites than Bituminous Coal due to the smaller size. The higher quantity of smaller cell sites in Coconut Shell Carbon can react quicker to adsorbing the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water, and retain these gases for longer periods of time than Bituminous Coal is capable of. The 1/2 micron Carbon Block Density assures better removal of contaminants by reducing the water flow or “Permeation” through the Block, and, minimizes water channeling associated with other Carbon filters. The solid Carbon Block provides 2 to 10 times more volume weight of filter material compared to other Granular Carbon, Block, and Fiber type filters by greatly reducing the porosity of the loose granules of Carbon, and void areas between fibers. This filter has also been known to be effective in reducing or removing Cysts and Bacteria such as Cryptosporidium, Cyclospora, Giardia, E-Coli, and Legionnaires Disease. This filter would normally be used as a post-filter for the Membrane Filter in a Reverse Osmosis system, or combined with other pre-filters in a Multi-stage Reverse Osmosis system, or as a stand alone filter for an ice-machine or single dispensing faucet. Other Carbon require more frequent service intervals and cartridge replacement. This filter offers the BEST protection against Fine  Sediments, Chlorine, Hydro-Carbon Gases, VOC’s, Cysts, Bacteria and other contaminants.

Recommended Service Interval on Most Water Supplies: 1 Year