DPF1/2MIMFAM - Substitute Sediment Pre-Filter for Ametek Part # 155002, 155014, 155071, 155182, C1 (Must Use With MEM24TFCAM or MEM18TFCAMB Membrane)
 

The CF1/2MILAM (1/2) .5 micron filter uses Solid Pressed Molded Carbon Block Technology to reduce or remove Cysts, Bacteria, Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, VOC’s, Fine Sediments, Silt, and Clay from untreated water. Small granules of Coconut Shell Carbon are Crushed into Powder, Pressed and Bonded together with a “PATENTED” heat molding process to form a solid BLOCK of Carbon that is encapsulated inside a plastic vessel housing. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The Block Density provides 2-10 times more Volume Weight of Filter Material when compared to other Inline GAC Carbon Filters, also allowing better filtration of the Fine Sediments, Silt, Clay, Cysts, and Bacteria. This filter provides the best protection against VOC’s, Hydro-Carbon Gas, Cyst and Bacteria Contaminants when used in a Reverse Osmosis Drinking Water System as either a Membrane or Storage Tank Post-filter. 
 

Recommended Service Interval on Most Water Supplies: 3 years

The MEM18TFCAMB .001 micron Membrane filter uses a Thin Film Composite Cellular Skin to separate and remove Dissolved Solids, Salts, Minerals, Heavy Metals, Organic Matter, Pyroxene’s, Sub-micron Colloidal matter, Cysts, Bacteria, and other contaminants from untreated water. Water containing Dissolved Minerals and other Contaminants is forced under high pressure through a Semi-Permeable, Spiral Wound, Thin Film Composite Cellular Skin layered in several wrappings, to separate and rinse away the dissolved solids to a sewage drain, leaving only the Pure, H20 water molecules for consumption, production, processing, or manufacturing. The TFC Membrane skin has a broader PH tolerance, can remove a higher maximum threshold of dissolved solids, and removes a higher percentage of dissolved solids than the CTA Membrane is capable of removing. The TFC Membrane can be used on Municipal or Well Water with proper pre-filtration. Typical Rejection of minerals and impurities for the TFC Membrane is 95%-99% removal, compared to 70%-80% for the CTA Membrane. This is the best Membrane available for Residential Reverse Osmosis Systems.
 

Recommended Service Interval on Most Water Supplies: 3 years

MEM18TFCAMB - Substitute Membrane Filter for Ametek Part # CTAB-10HF (Must Use With DPF1/2MIMFAM Dual-Purpose Filter)
 

The DPF1/2MIMFAM (1/2) .5 micron filter uses a Graded Density Core, Carbon Impregnated Micro-Fiber Technology to reduce or remove  Dirt, Iron, Sand, Sediment, Silt, Clay, Cysts, Bacteria, Chlorine, Ammonia Chloramines, Hydro-Carbon Gases, and other fine debris from untreated water. Coconut Shell Carbon Powder is impregnated into thousands of small Micro Fibers that are thermally fused together creating a Modified Carbon Block Filter. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The 1/2 micron Fiber Material Density, and Coconut Shell Carbon Powder combination provides 2-3 times more Volume Weight of Filter Material when compared to other Dual-Purpose Filters. This filter offers the best removal of Chlorine, Hydro-Carbon  Gases, Sediments, Silt, Clay, Cysts, and Bacteria when used as a Pre-filter for a Reverse Osmosis Drinking Water System. 

Recommended Service Interval on Most Water Supplies: 3 years

CF1/2MILAM - Substitute Inline Carbon Post-Filter for Ametek Part # IC-100-RO, IC101L, 155656-48

The DPF1/2MIMFAM (1/2) .5 micron filter uses a Graded Density Core, Carbon Impregnated Micro-Fiber Technology to reduce or remove  Dirt, Iron, Sand, Sediment, Silt, Clay, Cysts, Bacteria, Chlorine, Ammonia Chloramines, Hydro-Carbon Gases, and other fine debris from untreated water. Coconut Shell Carbon Powder is impregnated into thousands of small Micro Fibers that are thermally fused together creating a Modified Carbon Block Filter. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The 1/2 micron Fiber Material Density, and Coconut Shell Carbon Powder combination provides 2-3 times more Volume Weight of Filter Material when compared to other Dual-Purpose Filters. This filter offers the best removal of Chlorine, Hydro-Carbon  Gases, Sediments, Silt, Clay, Cysts, and Bacteria when used as a Pre-filter for a Reverse Osmosis Drinking Water System. 

Recommended Service Interval on Most Water Supplies: 1 years

DPF1/2MIMFAM - Substitute Sediment Pre-Filter for Ametek Part # 155002, 155014, 155071, 155182, C1 (Must Use With MEM24TFCAM or MEM18TFCAMB Membrane)

MEM24TFCAM - Substitute Membrane Filter for Ametek Part # 155349-01, 155415-01, 155431-19, CTAB-2-10HF, ROM-16C, ROM-26T (Must Use With DPF1/2MIMFAM Dual-Purpose Filter) > 18-100 gpd Membranes available

This .001micron Membrane filter uses a Thin Film Composite Cellular Skin to separate and remove Dissolved Solids, Salts, Minerals, Heavy Metals, Organic Matter, Pyroxene’s, Sub-micron Colloidal matter, Cysts, Bacteria, and other contaminants from untreated water. Water containing Dissolved Minerals and other Contaminants is forced under high pressure through a Semi-Permeable, Spiral Wound, Thin Film Composite Cellular Skin layered in several wrappings, to separate and rinse away the dissolved solids to a sewage drain, leaving only the Pure, H20 water molecules for consumption, production, processing, or manufacturing. The TFC Membrane skin has a broader PH tolerance than the CTA Membrane skin, it can remove a higher maximum threshold of dissolved solids, and removes a higher percentage of dissolved solids than the CTA Membrane is capable of removing. The TFC Membrane can be used on Municipal or Well Water with proper pre-filtration due the natural Bacteriostatic properties. Typical Rejection of minerals and impurities for the TFC Membrane is 95%-99% removal, compared to 70%-80% for the CTA Membrane. TFC Membranes are used in Vending machines and Bottled Water processing plants across the U.S.A. This is the best Membrane choice available for producing the highest purity water from a Residential Reverse Osmosis System.

Recommended Service Interval on Most Water Supplies: 3 years

CF1/2MCB-AM - Substitute Carbon Post-Filter for Ametek Part # 155109, 155155, 155155-43, CC-10, D20, GAC-10

This 10 micron filter uses Extruded Carbon Block Technology to reduce or remove Chlorine, and other Hydro-Carbon Gases from untreated water. Small granules of Bituminous Carbon are Crushed and bonded together with a proprietary Extrusion molding process to form a long, solid BLOCK of Carbon that is cut to specific lengths. Bituminous Carbon is mined from the Earth and does not possess the smaller cell site structure of Coconut Shell Carbon, so Bituminous Carbon IS NOT capable of reducing or removing VOC’s (Volatile Organic Chemicals), Ammonia, Chloramines, or other priority level Hydro-Carbon Gas contaminants that the 1/2 micron Carbon Block filter is capable of reducing or removing. And, the 10 micron rating results in less filter material volume weight per square inch which does not allow for removal of Silt, Clay, fine Sediments, Cysts or Bacteria that the 1/2 micron Carbon Block is capable of reducing or removing. The solid Carbon Block design provides 2 to 3 times more volume weight of filter material compared to other Granular Carbon and Fiber type filters by greatly reducing the porosity of the loose granules of Carbon. This filter would normally be used as a Pre-filter to reduce or remove Chlorine from the incoming water when combined with other pre-filters in a Multi-stage Reverse Osmosis system, or as a stand alone filter at a single dispensing  faucet, requiring frequent service intervals and cartridge replacement.
 

Recommended Service Interval on Most Water Supplies: 6 - 12 Months