The CF5MCBCLML 5 micron filter is a Proprietary product designed exclusively for the Microline filter housings, and with some Proprietary filter products the consumer compromises the Purity and Safety of their drinking water because of performance limitations associated with the size, design, and choice of material used in manufacturing the filter. This 5 micron filter uses Extruded Carbon Block Technology to reduce or remove Chlorine, and other Hydro-Carbon Gases from untreated water. Small granules of Bituminous Carbon are Crushed and bonded together with a proprietary Extrusion molding process to form a long, solid BLOCK of Carbon that is cut to specific lengths. Bituminous Carbon is mined from the Earth and does not possess the smaller cell site structure of Coconut Shell Carbon, so Bituminous Carbon IS NOT capable of reducing or removing VOC’s (Volatile Organic Chemicals), Ammonia, Chloramines, or other priority level Hydro-Carbon Gas contaminants that the 1/2 micron Carbon Block filter is capable of reducing or removing. And, the 5 micron rating results in less filter material volume weight per square inch which does not allow for removal of Silt, Clay, fine Sediments, Cysts or Bacteria that the 1/2 micron Carbon Block is capable of reducing or removing. The solid Carbon Block design provides 2 to 3 times more volume weight of filter material compared to other Granular Carbon and Fiber type filters by greatly reducing the porosity of the loose granules of Carbon. This filter would normally be used as a Pre-filter to reduce or remove Chlorine from the incoming water in a Multi-stage Reverse Osmosis system, or as a stand alone filter at a single dispensing  faucet, requiring frequent service intervals and cartridge replacement.

Recommended Service Interval on Most Water Supplies: 6-12 months

CF5MCBCLML - Substitute Sediment/Carbon Pre-Filter for Clack Microline Part # S7028, S7025 (Must use MEM35TFCCLML Membrane Filter or other TFC sizes)

The MEM35TFCCLML .001 micron Membrane filter is a Proprietary product designed exclusively for the Microline filter housings, and with some Proprietary filter products the consumer compromises the Purity and Safety of their drinking water because of performance limitations associated with the size, design, and choice of material used in manufacturing the filter. This .001 micron Membrane filter uses a Thin Film Composite Cellular Skin to separate and remove Dissolved Solids, Salts, Minerals, Heavy Metals, Organic Matter, Pyroxene’s, Sub-micron Colloidal matter, Cysts, Bacteria, and other contaminants from untreated water. Water containing Dissolved Minerals and other Contaminants is forced under high pressure through a Semi-Permeable, Spiral Wound, Thin Film Composite Cellular Skin layered in several wrappings, to separate and rinse away the dissolved solids to a sewage drain, leaving only the Pure, H20 water molecules for consumption, production, processing, or manufacturing. The TFC Membrane skin has a broader PH tolerance than the CTA Membrane skin, it can remove a higher maximum threshold of dissolved solids, and removes a higher percentage of dissolved solids than the CTA Membrane is capable of removing. The TFC Membrane can be used on Municipal or Well Water with proper pre-filtration due the natural Bacteriostatic properties. Typical Rejection of minerals and impurities for the TFC Membrane is 95%-99% removal, compared to 70%-80% for the CTA Membrane. TFC Membranes are used in Vending machines and Bottled Water processing plants across the U.S.A. This is the best Membrane choice available for producing the highest purity water from a Residential Reverse Osmosis System.

Recommended Service Interval on Most Water Supplies: 3 years

MEM35TFCCLML - Substitute 35 gpd Membrane Filter for Clack Microline Part # S1229-RS (Must Use With CFMCBCLML Sediment/Carbon Filter) > 18-150 gpd Membranes available for part # S1224-RS (14 gpd), S1227-RS (25 gpd)

The CF5MCBCLML 5 micron filter is a Proprietary product designed exclusively for the Microline filter housings, and with some Proprietary filter products the consumer compromises the Purity and Safety of their drinking water because of performance limitations associated with the size, design, and choice of material used in manufacturing the filter. This 5 micron filter uses Extruded Carbon Block Technology to reduce or remove Chlorine, and other Hydro-Carbon Gases from untreated water. Small granules of Bituminous Carbon are Crushed and bonded together with a proprietary Extrusion molding process to form a long, solid BLOCK of Carbon that is cut to specific lengths. Bituminous Carbon is mined from the Earth and does not possess the smaller cell site structure of Coconut Shell Carbon, so Bituminous Carbon IS NOT capable of reducing or removing VOC’s (Volatile Organic Chemicals), Ammonia, Chloramines, or other priority level Hydro-Carbon Gas contaminants that the 1/2 micron Carbon Block filter is capable of reducing or removing. And, the 5 micron rating results in less filter material volume weight per square inch which does not allow for removal of Silt, Clay, fine Sediments, Cysts or Bacteria that the 1/2 micron Carbon Block is capable of reducing or removing. The solid Carbon Block design provides 2 to 3 times more volume weight of filter material compared to other Granular Carbon and Fiber type filters by greatly reducing the porosity of the loose granules of Carbon. This filter would normally be used as a Post-filter for a Reverse Osmosis system, or combined with other pre-filters in a Multi-stage Reverse Osmosis system to reduce or remove Chlorine from the incoming water supply, or as a stand alone filter at a single dispensing faucet.

Recommended Service Interval on Most Water Supplies: 6-12 months

CF5MCBCLML - Substitute Carbon Block Post-Filter for Clack Microline Part # S7028, S7025 (Must use MEM35TFCCLML Membrane Filter or other TFC sizes)

The CF1/2MILCLML 1/2 micron filter uses Solid Pressed Molded Carbon Block Technology to reduce or remove Cysts, Bacteria, Fungus, Algae, Chlorine, Ammonia, Chloramines, Hydro-Carbon  Gases, and VOC’s (Volatile Organic Chemicals) from untreated water. Small granules of Coconut Shell Carbon are Crushed, Pressed and Bonded together with a “PATENTED” heat molding process to form a solid BLOCK or Brick of Carbon that is encapsulated inside a plastic vessel housing. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering almost twice as many cell sites than Bituminous Coal due to the smaller size. The higher quantity of smaller cell sites in Coconut Shell Carbon can react quicker to adsorbing the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water, and retain these gases for longer periods of time than Bituminous Coal is capable of. The 1/2 micron Carbon Block Density assures better removal of contaminants by reducing the water flow or “Permeation” through the Block, and, minimizes water channeling associated with other Carbon filters. The solid Carbon Block provides 2 to 10 times more volume weight of filter material compared to other Granular Carbon, Block, and Fiber type filters by greatly reducing the porosity of the loose granules of Carbon, and void areas between fibers. This filter has also been known to be effective in reducing or removing Cysts and Bacteria such as Cryptosporidium, Cyclospora, Giardia, E-Coli, and Legionnaires Disease. This filter would normally be used as a post-filter for the Membrane Filter in a Reverse Osmosis system, or combined with other pre-filters in a Multi-stage Reverse Osmosis system, or as a stand alone filter for an ice-machine or single dispensing faucet. Other Carbon require more frequent service intervals and cartridge replacement. This filter offers the BEST protection against Fine  Sediments, Chlorine, Hydro-Carbon Gases, VOC’s, Cysts, Bacteria and other contaminants.

Recommended Service Interval on Most Water Supplies: 6-12 months

CF1/2MILCLML - Substitute Inline Carbon Post-Filter for Clack Microline Part # S7206-06C, S7206W

CF5MCBCLML - Substitute Sediment/Carbon Pre-Filter for Clack Microline Part # S7028, S7025 (Must use MEM35TFCCLML Membrane Filter or other TFC sizes)

The CF5MCBCLML 5 micron filter is a Proprietary product designed exclusively for the Microline filter housings, and with some Proprietary filter products the consumer compromises the Purity and Safety of their drinking water because of performance limitations associated with the size, design, and choice of material used in manufacturing the filter. This 5 micron filter uses Extruded Carbon Block Technology to reduce or remove Chlorine, and other Hydro-Carbon Gases from untreated water. Small granules of Bituminous Carbon are Crushed and bonded together with a proprietary Extrusion molding process to form a long, solid BLOCK of Carbon that is cut to specific lengths. Bituminous Carbon is mined from the Earth and does not possess the smaller cell site structure of Coconut Shell Carbon, so Bituminous Carbon IS NOT capable of reducing or removing VOC’s (Volatile Organic Chemicals), Ammonia, Chloramines, or other priority level Hydro-Carbon Gas contaminants that the 1/2 micron Carbon Block filter is capable of reducing or removing. And, the 5 micron rating results in less filter material volume weight per square inch which does not allow for removal of Silt, Clay, fine Sediments, Cysts or Bacteria that the 1/2 micron Carbon Block is capable of reducing or removing. The solid Carbon Block design provides 2 to 3 times more volume weight of filter material compared to other Granular Carbon and Fiber type filters by greatly reducing the porosity of the loose granules of Carbon. This filter would normally be used as a Pre-filter to reduce or remove Chlorine from the incoming water in a Multi-stage Reverse Osmosis system, or as a stand alone filter at a single dispensing  faucet, requiring frequent service intervals and cartridge replacement.

Recommended Service Interval on Most Water Supplies: 6-12 months

MEM35TFCCLML - Substitute 35 gpd Membrane Filter for Clack Microline Part # S1229-RS (Must Use With CFMCBCLML Sediment/Carbon Filter) > 18-150 gpd Membranes available for part # S1224-RS (14 gpd), S1227-RS (25 gpd)

The MEM35TFCCLML .001 micron Membrane filter is a Proprietary product designed exclusively for the Microline filter housings, and with some Proprietary filter products the consumer compromises the Purity and Safety of their drinking water because of performance limitations associated with the size, design, and choice of material used in manufacturing the filter. This .001 micron Membrane filter uses a Thin Film Composite Cellular Skin to separate and remove Dissolved Solids, Salts, Minerals, Heavy Metals, Organic Matter, Pyroxene’s, Sub-micron Colloidal matter, Cysts, Bacteria, and other contaminants from untreated water. Water containing Dissolved Minerals and other Contaminants is forced under high pressure through a Semi-Permeable, Spiral Wound, Thin Film Composite Cellular Skin layered in several wrappings, to separate and rinse away the dissolved solids to a sewage drain, leaving only the Pure, H20 water molecules for consumption, production, processing, or manufacturing. The TFC Membrane skin has a broader PH tolerance than the CTA Membrane skin, it can remove a higher maximum threshold of dissolved solids, and removes a higher percentage of dissolved solids than the CTA Membrane is capable of removing. The TFC Membrane can be used on Municipal or Well Water with proper pre-filtration due the natural Bacteriostatic properties. Typical Rejection of minerals and impurities for the TFC Membrane is 95%-99% removal, compared to 70%-80% for the CTA Membrane. TFC Membranes are used in Vending machines and Bottled Water processing plants across the U.S.A. This is the best Membrane choice available for producing the highest purity water from a Residential Reverse Osmosis System.

Recommended Service Interval on Most Water Supplies: 3 years

CF5MCBCLML - Substitute Carbon Block Post-Filter for Clack Microline Part # S7028, S7025 (Must use MEM35TFCCLML Membrane Filter or other TFC sizes)

The CF5MCBCLML 5 micron filter is a Proprietary product designed exclusively for the Microline filter housings, and with some Proprietary filter products the consumer compromises the Purity and Safety of their drinking water because of performance limitations associated with the size, design, and choice of material used in manufacturing the filter. This 5 micron filter uses Extruded Carbon Block Technology to reduce or remove Chlorine, and other Hydro-Carbon Gases from untreated water. Small granules of Bituminous Carbon are Crushed and bonded together with a proprietary Extrusion molding process to form a long, solid BLOCK of Carbon that is cut to specific lengths. Bituminous Carbon is mined from the Earth and does not possess the smaller cell site structure of Coconut Shell Carbon, so Bituminous Carbon IS NOT capable of reducing or removing VOC’s (Volatile Organic Chemicals), Ammonia, Chloramines, or other priority level Hydro-Carbon Gas contaminants that the 1/2 micron Carbon Block filter is capable of reducing or removing. And, the 5 micron rating results in less filter material volume weight per square inch which does not allow for removal of Silt, Clay, fine Sediments, Cysts or Bacteria that the 1/2 micron Carbon Block is capable of reducing or removing. The solid Carbon Block design provides 2 to 3 times more volume weight of filter material compared to other Granular Carbon and Fiber type filters by greatly reducing the porosity of the loose granules of Carbon. This filter would normally be used as a Post-filter for a Reverse Osmosis system, or combined with other pre-filters in a Multi-stage Reverse Osmosis system to reduce or remove Chlorine from the incoming water supply, or as a stand alone filter at a single dispensing faucet.

Recommended Service Interval on Most Water Supplies: 6-12 months