This 10 micron filter is designed to offer the consumer 2 stages of filtration in a single, compact, cartridge element, using Conventional Core, Carbon Impregnated Micro-Fiber Technology encapsulated inside of a Proprietary Plastic Housing to reduce or remove Sediments, Sand, Rocks, Chlorine, Hydro-Carbon Gases, and other large debris from untreated water. Minimal amounts of Small Bituminous Carbon granules are crushed into a powder and impregnated into thousands of small micro fibers that are thermally fused and bonded together around a plastic center core to form a Modified Carbon Block cartridge. This filter DOES NOT offer Graduated Depth Filtration, resulting in less filter material volume weight per square inch due to the inefficiency of cartridge design which allows the cartridge to become easily saturated and fouled under excessive Sediment input, and requires more frequent service intervals and cartridge replacement. The Bituminous Carbon is mined from the Earth and does not possess the smaller cell site structure of Coconut Shell Carbon, so Bituminous Carbon IS NOT capable of reducing or removing VOC’s (Volatile Organic Chemicals), Ammonia, Chloramines, or other priority level Hydro-Carbon Gas contaminants that a 1/2 micron Modified Carbon Block filter is capable of reducing or removing. Due to the inefficiency of this cartridge design, limited volume of filter material, and larger 5 micron rating, this filter does not allow for removal of any Silt, Clay, Fine Sediments, Cysts or Bacteria that a standard size 1/2 micron Modified Carbon Block is capable of reducing or removing. This filter would normally be used as a Pre-filter to reduce or remove Sediment and Chlorine from the incoming water when combined with other pre-filters in a Multi-stage Reverse Osmosis system, or as a stand alone filter at a single dispensing faucet. However, the consumer must realize that the Silt, Clay, Fine Sediments, Cysts, Bacteria, other debris, and eventually Chlorine Gases will pass through this filter when used in a Reverse Osmosis system, which leads to Fouling, and Damage of the Membrane Filter, requiring frequent service intervals and cartridge replacement. The Proprietary design restricts the consumer to only one choice of filter cartridge selection and one distribution entity when replacing expired or exhausted filters, which typically imposes a higher retail price and compromise in quality and performance.

Recommended Service Interval on Most Water Supplies: 1-3 months

DPF10MIMFUSFE - Sediment/Carbon Pre-Filter for US Filter Part # HP 4755706, 47-55706G2

This .001 micron Membrane filter uses a Thin Film Composite Cellular Skin encapsulated inside of a Proprietary Plastic Housing to separate and remove Dissolved Solids, Salts, Minerals, Heavy Metals, Organic Matter, Pyroxene’s, Sub-micron Colloidal matter, Cysts, Bacteria, and other contaminants from untreated water. Water containing Dissolved Minerals and other Contaminants is forced under high pressure through a Semi-Permeable, Spiral Wound, Thin Film Composite Cellular Skin layered in several wrappings, to separate and rinse away the dissolved solids to a sewage drain, leaving only the Pure, H20 water molecules for consumption, production, processing, or manufacturing. The TFC Membrane skin has a broader PH tolerance than the CTA Membrane skin, it can remove a higher maximum threshold of dissolved solids, and removes a higher percentage of dissolved solids than the CTA Membrane is capable of removing. The TFC Membrane can be used on Municipal or Well Water with proper pre-filtration due the natural Bacteriostatic properties. Typical Rejection of minerals and impurities for the TFC Membrane is 95%-99% removal, compared to 70%-80% for the CTA Membrane. TFC Membranes are used in Vending machines and Bottled Water processing plants across the U.S.A. The Proprietary design restricts the consumer to only one choice of filter cartridge selection and one distribution entity when replacing expired or exhausted filters, which typically imposes a higher retail price and compromise in quality and performance. This is the best Membrane choice available for producing the highest purity water from a Residential Reverse Osmosis System.

Recommended Service Interval on Most Water Supplies: 3 years

MEM18TFCUSFE - (18 gpd) Substitute Membrane Filter for US Filter Part # HP 6647032, 66-4507G2 (must use the DPF10MIMFUSF Pre-Filter) > 18-80 gpd Membranes available: MEM30TFCUSFE (30 gpd), MEM50TFCUSFE (50 gpd), MEM80TFCUSFE (80 gpd)

This 10 micron filter uses Extruded Carbon Block Technology encapsulated inside of a Proprietary Plastic Housing to reduce or remove Chlorine, and other Hydro-Carbon Gases from untreated water. Small granules of Bituminous Carbon are Crushed and bonded together with a proprietary Extrusion molding process to form a long, solid BLOCK of Carbon that is cut to specific lengths. Bituminous Carbon is mined from the Earth and does not possess the smaller cell site structure of Coconut Shell Carbon, so Bituminous Carbon IS NOT capable of reducing or removing VOC’s (Volatile Organic Chemicals), Ammonia, Chloramines, or other priority level Hydro-Carbon Gas contaminants that a 1/2 micron Carbon Block filter is capable of reducing or removing. And, the 10 micron rating results in less filter material volume weight per square inch which does not allow for removal of Silt, Clay, Fine Sediments, Cysts or Bacteria that a 1/2 micron Carbon Block is capable of reducing or removing. The solid Carbon Block design provides 2 to 3 times more volume weight of filter material compared to other Granular Carbon and Fiber type filters by greatly reducing the porosity of the loose granules of Carbon. This filter would normally be used as a Pre-filter to reduce or remove Chlorine from the incoming water when combined with other pre-filters in a Multi-stage Reverse Osmosis system, or as a stand alone filter at a single dispensing  faucet, requiring frequent service intervals and cartridge replacement. This filter utilizes a Proprietary design which restricts the consumer to only one choice of filter cartridge selection and one distribution entity when replacing expired or exhausted filters, which typically imposes a higher retail price and compromise in quality and performance.

Recommended Service Interval on Most Water Supplies: 3-6 months

CF10MCBUSFE - Substitute Carbon Post-Filter for US Filter Part # HP 4755710, 47-55710G2

DPF20MIPUSF - Substitute Sediment Pre-Filter for US Filter Part # D-20 (use with the  MEM18TFCUSF Membrane Filter)

This 20 micron filter is designed to offer the consumer 2 stages of filtration in a single, compact, Proprietary size cartridge element, using Carbon Impregnated Cellulose Paper Technology to reduce or remove Sediments, Sand, Rocks, Chlorine, Hydro-Carbon Gases, and other large debris from untreated water. Minimal amounts of Small Bituminous Carbon granules are crushed into a powder and impregnated onto sheets of cellulose paper and rolled around a plastic center core. Rubber end caps are added for additional structural support of the rolled paper, but promotes the Growth of Bacteria on the rubber material which causes a health risk. Bituminous Carbon is mined from the Earth and does not possess the smaller cell site structure of Coconut Shell Carbon, so Bituminous Carbon IS NOT capable of reducing or removing VOC’s (Volatile Organic Chemicals) Ammonia, Chloramines, or other priority level Hydro-Carbon Gas contaminants that the 1/2 micron Modified Carbon Block filter is capable of reducing or removing. Due to the inefficiency of this cartridge design, limited volume of filter material, and larger 20 micron rating, this filter does not allow for removal of any Silt, Clay, Fine Sediments, Cysts or Bacteria that the 1/2 micron Modified Carbon Block is capable of reducing or removing. This filter would normally be used as a Pre-filter to reduce or remove Sediment and Chlorine from the incoming water when combined with other pre-filters in a Multi-stage Reverse Osmosis system, or as a stand alone filter at a single dispensing faucet. However, the consumer must realize that the Silt, Clay, Fine Sediments, Cysts, Bacteria, other debris, and eventually Chlorine Gases will pass through this filter when used in a Reverse Osmosis system, which leads to Fouling, and Damage of the Membrane Filter, requiring frequent service intervals and cartridge replacement.

Recommended Service Interval on Most Water Supplies: 1-3 months

This .001 micron Membrane filter uses a Proprietary size Thin Film Composite Cellular Skin element to separate and remove Dissolved Solids, Salts, Minerals, Heavy Metals, Organic Matter, Pyroxene’s, Sub-micron Colloidal matter, Cysts, Bacteria, and other contaminants from untreated water. Water containing Dissolved Minerals and other Contaminants is forced under high pressure through a Semi-Permeable, Spiral Wound, Thin Film Composite Cellular Skin layered in several wrappings, to separate and rinse away the dissolved solids to a sewage drain, leaving only the Pure, H20 water molecules for consumption, production, processing, or manufacturing. The TFC Membrane skin has a broader PH tolerance than the CTA Membrane skin, it can remove a higher maximum threshold of dissolved solids, and removes a higher percentage of dissolved solids than the CTA Membrane is capable of removing. The TFC Membrane can be used on Municipal or Well Water with proper pre-filtration due the natural Bacteriostatic properties. Typical Rejection of minerals and impurities for the TFC Membrane is 95%-99% removal, compared to 70%-80% for the CTA Membrane. TFC Membranes are used in Vending machines and Bottled Water processing plants across the U.S.A. This is the best Membrane choice available for producing the highest purity water from a Residential Reverse Osmosis System.

Recommended Service Interval on Most Water Supplies: 3 years

MEM18TFCUSF - 18 gpd Substitute Membrane Filter for US Filter Part # ROM-230T (must use the DPF20MIPUSF Pre-Filter)

This 20 micron filter is designed to offer the consumer 2 stages of filtration in a single, compact, Proprietary size cartridge element, using Carbon Impregnated Cellulose Paper Technology to reduce or remove Sediments, Sand, Rocks, Chlorine, Hydro-Carbon Gases, and other large debris from untreated water. Minimal amounts of Small Bituminous Carbon granules are crushed into a powder and impregnated onto sheets of cellulose paper and rolled around a plastic center core. Rubber end caps are added for additional structural support of the rolled paper, but promotes the Growth of Bacteria on the rubber material which causes a health risk. Bituminous Carbon is mined from the Earth and does not possess the smaller cell site structure of Coconut Shell Carbon, so Bituminous Carbon IS NOT capable of reducing or removing VOC’s (Volatile Organic Chemicals) Ammonia, Chloramines, or other priority level Hydro-Carbon Gas contaminants that the 1/2 micron Modified Carbon Block filter is capable of reducing or removing. Due to the inefficiency of this cartridge design, limited volume of filter material, and larger 20 micron rating, this filter does not allow for removal of any Silt, Clay, Fine Sediments, Cysts or Bacteria that the 1/2 micron Modified Carbon Block is capable of reducing or removing. This filter would normally be used as a Pre-filter to reduce or remove Sediment and Chlorine from the incoming water when combined with other pre-filters in a Multi-stage Reverse Osmosis system, or as a stand alone filter at a single dispensing faucet. However, the consumer must realize that the Silt, Clay, Fine Sediments, Cysts, Bacteria, other debris, and eventually Chlorine Gases will pass through this filter when used in a Reverse Osmosis system, which leads to Fouling, and Damage of the Membrane Filter, requiring frequent service intervals and cartridge replacement.

Recommended Service Interval on Most Water Supplies: 1-3 months

DPF20MIPUSF - Substitute Carbon Post-Filter for US Filter Part # D-15

SED5MMFUSFE - Sediment Pre-Filter #1 for US Filter Part # HP 4755702, 47-55702G2

This 5 micron filter uses Conventional Core, Micro-Fiber technology encapsulated inside of a Proprietary Plastic Housing to remove Dirt, Rocks, Sand, Sticks, Bugs, and other large debris from untreated water. This filter is manufactured by thermally fusing thousands of small micro fibers together. This filter DOES NOT offer Graduated Depth Filtration, resulting in less filter material volume weight per square inch due to the inefficiency of cartridge design which allows the cartridge to become easily saturated and fouled under excessive Sediment input, and requires more frequent service intervals and cartridge replacement. Cysts, Bacteria, and Super Fine Silt, Clay, and Debris WILL NOT be removed by this filter and will be passed on to the Membrane Filter if used in a Reverse Osmosis System, which would eventually result in premature Membrane failure. This filter would normally be used as a pre-filter for single dispensing faucets in a Bathroom, Kitchen Sink, or an Island Sink to prevent faucet screens from plugging, or, combined with other Pre-filters in a Multi-stage Reverse Osmosis system when used on Well Water, or, as a stand alone filter. This filter can be used successfully in a Multi-Stage Reverse Osmosis System as a Primary Pre-filter providing a 1 micron or lower micron Filter is used as the Secondary Pre-filter to trap the Silt, Clay, Bacteria, and Super Fine Sediments before entering the Membrane Filter. The Proprietary design restricts the consumer to only one choice of filter cartridge selection and one distribution entity when replacing expired or exhausted filters, which typically imposes a higher retail price and compromise in quality and performance.

Recommended Service Interval on Most Water Supplies: 3-6 months

This 10 micron filter is designed to offer the consumer 2 stages of filtration in a single, compact, cartridge element, using Conventional Core, Carbon Impregnated Micro-Fiber Technology encapsulated inside of a Proprietary Plastic Housing to reduce or remove Sediments, Sand, Rocks, Chlorine, Hydro-Carbon Gases, and other large debris from untreated water. Minimal amounts of Small Bituminous Carbon granules are crushed into a powder and impregnated into thousands of small micro fibers that are thermally fused and bonded together around a plastic center core to form a Modified Carbon Block cartridge. This filter DOES NOT offer Graduated Depth Filtration, resulting in less filter material volume weight per square inch due to the inefficiency of cartridge design which allows the cartridge to become easily saturated and fouled under excessive Sediment input, and requires more frequent service intervals and cartridge replacement. The Bituminous Carbon is mined from the Earth and does not possess the smaller cell site structure of Coconut Shell Carbon, so Bituminous Carbon IS NOT capable of reducing or removing VOC’s (Volatile Organic Chemicals), Ammonia, Chloramines, or other priority level Hydro-Carbon Gas contaminants that a 1/2 micron Modified Carbon Block filter is capable of reducing or removing. Due to the inefficiency of this cartridge design, limited volume of filter material, and larger 5 micron rating, this filter does not allow for removal of any Silt, Clay, Fine Sediments, Cysts or Bacteria that a standard size 1/2 micron Modified Carbon Block is capable of reducing or removing. This filter would normally be used as a Pre-filter to reduce or remove Sediment and Chlorine from the incoming water when combined with other pre-filters in a Multi-stage Reverse Osmosis system, or as a stand alone filter at a single dispensing faucet. However, the consumer must realize that the Silt, Clay, Fine Sediments, Cysts, Bacteria, other debris, and eventually Chlorine Gases will pass through this filter when used in a Reverse Osmosis system, which leads to Fouling, and Damage of the Membrane Filter, requiring frequent service intervals and cartridge replacement. The Proprietary design restricts the consumer to only one choice of filter cartridge selection and one distribution entity when replacing expired or exhausted filters, which typically imposes a higher retail price and compromise in quality and performance.

Recommended Service Interval on Most Water Supplies: 1-3 months

DPF10MIMFUSFE - Sediment/Carbon Pre-Filter #2 for US Filter Part # HP 4755704, 47-55704G2, HP 4755706, 47-55706G2

This .001 micron Membrane filter uses a Thin Film Composite Cellular Skin encapsulated inside of a Proprietary Plastic Housing to separate and remove Dissolved Solids, Salts, Minerals, Heavy Metals, Organic Matter, Pyroxene’s, Sub-micron Colloidal matter, Cysts, Bacteria, and other contaminants from untreated water. Water containing Dissolved Minerals and other Contaminants is forced under high pressure through a Semi-Permeable, Spiral Wound, Thin Film Composite Cellular Skin layered in several wrappings, to separate and rinse away the dissolved solids to a sewage drain, leaving only the Pure, H20 water molecules for consumption, production, processing, or manufacturing. The TFC Membrane skin has a broader PH tolerance than the CTA Membrane skin, it can remove a higher maximum threshold of dissolved solids, and removes a higher percentage of dissolved solids than the CTA Membrane is capable of removing. The TFC Membrane can be used on Municipal or Well Water with proper pre-filtration due the natural Bacteriostatic properties. Typical Rejection of minerals and impurities for the TFC Membrane is 95%-99% removal, compared to 70%-80% for the CTA Membrane. TFC Membranes are used in Vending machines and Bottled Water processing plants across the U.S.A. The Proprietary design restricts the consumer to only one choice of filter cartridge selection and one distribution entity when replacing expired or exhausted filters, which typically imposes a higher retail price and compromise in quality and performance. This is the best Membrane choice available for producing the highest purity water from a Residential Reverse Osmosis System.

Recommended Service Interval on Most Water Supplies: 3 years

MEM18TFCUSFE (18 gpd) - Substitute Membrane Filter for US Filter Part # HP 6647032, 66-4507G2 > 18-80 gpd Membranes available: MEM30TFCUSFE (30 gpd), MEM50TFCUSFE (50 gpd), MEM80TFCUSFE (80 gpd)

This 10 micron filter uses Extruded Carbon Block Technology encapsulated inside of a Proprietary Plastic Housing to reduce or remove Chlorine, and other Hydro-Carbon Gases from untreated water. Small granules of Bituminous Carbon are Crushed and bonded together with a proprietary Extrusion molding process to form a long, solid BLOCK of Carbon that is cut to specific lengths. Bituminous Carbon is mined from the Earth and does not possess the smaller cell site structure of Coconut Shell Carbon, so Bituminous Carbon IS NOT capable of reducing or removing VOC’s (Volatile Organic Chemicals), Ammonia, Chloramines, or other priority level Hydro-Carbon Gas contaminants that a 1/2 micron Carbon Block filter is capable of reducing or removing. And, the 10 micron rating results in less filter material volume weight per square inch which does not allow for removal of Silt, Clay, Fine Sediments, Cysts or Bacteria that a 1/2 micron Carbon Block is capable of reducing or removing. The solid Carbon Block design provides 2 to 3 times more volume weight of filter material compared to other Granular Carbon and Fiber type filters by greatly reducing the porosity of the loose granules of Carbon. This filter would normally be used as a Pre-filter to reduce or remove Chlorine from the incoming water when combined with other pre-filters in a Multi-stage Reverse Osmosis system, or as a stand alone filter at a single dispensing  faucet, requiring frequent service intervals and cartridge replacement. This filter utilizes a Proprietary design which restricts the consumer to only one choice of filter cartridge selection and one distribution entity when replacing expired or exhausted filters, which typically imposes a higher retail price and compromise in quality and performance.

Recommended Service Interval on Most Water Supplies: 3-6 months

CF10MCBUSFE - Substitute Carbon Post-Filter for US Filter Part # HP 4755710, 47-55710G2