The DPF1MIMWFS 1 micron filter uses a Graded Density Core, Carbon Impregnated Micro-Fiber Technology to reduce or remove  Dirt, Iron, Sand, Sediment, Silt, Clay, Cysts, Bacteria, Chlorine, Ammonia Chloramines, Hydro-Carbon Gases, and other fine debris from untreated water. Coconut Shell Carbon Powder is impregnated into thousands of small Micro Fibers that are thermally fused together creating a Modified Carbon Block Filter. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The 1 micron Fiber Material Density, and Coconut Shell Carbon Powder combination provides 2-3 times more Volume Weight of Filter Material when compared to other Dual-Purpose Filters. This filter offers next to the best removal of Chlorine, Hydro-Carbon Gases, Sediments, Silt, Clay, Cysts, and Bacteria when used as a Primary Pre-filter for a Reverse Osmosis Drinking Water System.

Recommended Service Interval on Most Water Supplies: 3 years

DPF1MIMWFS - Substitute Sediment Pre-Filter for Water Factory Systems Part # 47-1212419

The DPF1/2MIMFWFS (1/2) .5 micron filter uses a Graded Density Core, Carbon Impregnated Micro-Fiber Technology to reduce or remove  Dirt, Iron, Sand, Sediment, Silt, Clay, Cysts, Bacteria, Chlorine, Ammonia Chloramines, Hydro-Carbon Gases, and other fine debris from untreated water. Coconut Shell Carbon Powder is impregnated into thousands of small Micro Fibers that are thermally fused together creating a Modified Carbon Block Filter. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The 1/2 micron Fiber Material Density, and Coconut Shell Carbon Powder combination provides 2-3 times more Volume Weight of Filter  Material when compared to other Dual-Purpose Filters. This filter offers the best removal of Chlorine, Hydro-Carbon Gases, Sediments, Silt, Clay, Cysts, and Bacteria when used as a Primary or Secondary Pre-filter for a Reverse Osmosis Drinking Water System.

Recommended Service Interval on Most Water Supplies: 3 years

DPF1/2MIMFWFS - Substitute Sediment/Carbon Pre-Filter for Water Factory Systems Part # 47-211114 (Must Use With MEM18TFCWFS, MEM30TFCWFS, MEM80TFCWFS TFC Membrane Filter)

The MEM18TFCWFS, MEM30TFCWFS, MEM80TFCWFS .001 micron TFC Membrane filter uses a Thin Film Composite Cellular Skin to separate and remove Dissolved Solids, Salts, Minerals, Heavy Metals, Organic Matter, Pyroxene’s, Sub-micron Colloidal matter, Cysts, Bacteria, and other contaminants from untreated water. Water containing Dissolved Minerals and other Contaminants is forced under high pressure through a Semi-Permeable, Spiral Wound, Thin Film Composite Cellular Skin layered in several wrappings, to separate and rinse away the dissolved solids to a sewage drain, leaving only the Pure, H20 water molecules for consumption, production, processing, or manufacturing. The TFC Membrane skin has a broader PH tolerance, can remove a higher maximum threshold of dissolved solids, and removes a higher percentage of dissolved solids than the CTA Membrane is capable of removing. The TFC Membrane can be used on Municipal or Well Water with proper pre-filtration. Typical Rejection of minerals and impurities for the TFC Membrane is 95%-99% removal, compared to 70%-80% for the CTA Membrane. This is the best Membrane available for Residential Reverse Osmosis Systems.

Recommended Service Interval on Most Water Supplies: 3 years

MEM18TFCWFS (18 gpd), MEM30TFCWFS (30 gpd), MEM80TFCWFS (80 gpd) - Substitute TFC Membrane Filter for Water Factory Systems Part # 66-42019, 66-42039, 66-43019, 66-43037, 66-43101 (Must Use With DPF1/2MIMFWFS Sediment/Carbon Pre-Filter)> 12-150 gpd Membranes Available

The CF1/2MILWFS (1/2) .5 micron filter uses Solid Pressed Molded Carbon Block Technology to reduce or remove Cysts, Bacteria, Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, VOC’s, Fine Sediments, Silt, and Clay from untreated water. Small granules of Coconut Shell Carbon are Crushed into Powder, Pressed and Bonded together with a “PATENTED” heat molding process to form a solid BLOCK of Carbon that is encapsulated inside a plastic vessel housing. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The Block Density provides 2-10 times more Volume Weight of Filter Material when compared to other Inline GAC Carbon Filters, also allowing better filtration of the Fine Sediments, Silt, Clay, Cysts, and Bacteria. This filter provides the best protection against VOC’s, Hydro-Carbon Gas, Cyst and Bacteria Contaminants when used in a Reverse Osmosis Drinking Water System as either a Membrane or Storage Tank Post-filter. 

Recommended Service Interval on Most Water Supplies: 3 years

CF1/2MILWFS - Substitute Inline Carbon Post-Filter for Hague Part # 47-211212

The CF1/2MCBWFS (½) .5 micron filter uses Solid Pressed Molded Carbon Block Technology to reduce or remove Cysts, Bacteria, Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, VOC’s, Fine Sediments, Silt, and Clay from untreated water. Small granules of Coconut Shell Carbon are Crushed into Powder, Pressed and Bonded together with a “PATENTED” heat molding process to form a solid BLOCK of Carbon. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The Block Density provides 2-10 times more Volume Weight of Filter Material when compared to other Carbon Filters, also allowing better filtration of the Fine  Sediments, Silt, Clay, Cysts, and Bacteria. This filter provides the best protection against VOC’s, Hydro-Carbon Gas, Cyst and Bacteria Contaminants when used in a Reverse Osmosis Drinking Water System as a Storage Tank Post-filter.

Recommended Service Interval on Most Water Supplies: 3 years

CF1/2MCBWFS - Substitute Carbon Post-Filter for Water Factory Systems Part # 47-211114

The DPF1/2MIMFWFS (1/2) .5 micron filter uses a Graded Density Core, Carbon Impregnated Micro-Fiber Technology to reduce or remove  Dirt, Iron, Sand, Sediment, Silt, Clay, Cysts, Bacteria, Chlorine, Ammonia Chloramines, Hydro-Carbon Gases, and other fine debris from untreated water. Coconut Shell Carbon Powder is impregnated into thousands of small Micro Fibers that are thermally fused together creating a Modified Carbon Block Filter. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The 1/2 micron Fiber Material Density, and Coconut Shell Carbon Powder combination provides 2-3 times more Volume Weight of Filter  Material when compared to other Dual-Purpose Filters. This filter offers the best removal of Chlorine, Hydro-Carbon Gases, Sediments, Silt, Clay, Cysts, and Bacteria when used as a Primary or Secondary Pre-filter for a Reverse Osmosis Drinking Water System.

Recommended Service Interval on Most Water Supplies: 3 years

DPF1/2MIMFWFS - Substitute Sediment/Carbon Pre-Filter for Water Factory Systems Part # 47-211114 (Must Use With MEM18TFCWFS, MEM30TFCWFS, MEM80TFCWFS TFC Membrane Filter)

The MEM18TFCWFS, MEM30TFCWFS, MEM80TFCWFS .001 micron Membrane filter uses a Thin Film Composite Cellular Skin to separate and remove Dissolved Solids, Salts, Minerals, Heavy Metals, Organic Matter, Pyroxene’s, Sub-micron Colloidal matter, Cysts, Bacteria, and other contaminants from untreated water. Water containing Dissolved Minerals and other Contaminants is forced under high pressure through a Semi-Permeable, Spiral Wound, Thin Film Composite Cellular Skin layered in several wrappings, to separate and rinse away the dissolved solids to a sewage drain, leaving only the Pure, H20 water molecules for consumption, production, processing, or manufacturing. The TFC Membrane skin has a broader PH tolerance, can remove a higher maximum threshold of dissolved solids, and removes a higher percentage of dissolved solids than the CTA Membrane is capable of removing. The TFC Membrane can be used on Municipal or Well Water with proper pre-filtration. Typical Rejection of minerals and impurities for the TFC Membrane is 95%-99% removal, compared to 70%-80% for the CTA Membrane. This is the best Membrane available for Residential Reverse Osmosis Systems.

Recommended Service Interval on Most Water Supplies: 3 years

MEM18TFCWFS, MEM30TFCWFS, MEM80TFCWFS - Substitute Membrane Filter for Water Factory Systems Part # 66-42019, 66-42039, 66-43019, 66-43037, 66-43101 (Must Use With DPF1/2MIMFWFS Sediment/Carbon Pre-Filter)> 12-150 gpd Membranes Available

The CF1/2MILWFS (1/2) .5 micron filter uses Solid Pressed Molded Carbon Block Technology to reduce or remove Cysts, Bacteria, Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, VOC’s, Fine Sediments, Silt, and Clay from untreated water. Small granules of Coconut Shell Carbon are Crushed into Powder, Pressed and Bonded together with a “PATENTED” heat molding process to form a solid BLOCK of Carbon that is encapsulated inside a plastic vessel housing. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The Block Density provides 2-10 times more Volume Weight of Filter Material when compared to other Inline GAC Carbon Filters, also allowing better filtration of the Fine Sediments, Silt, Clay, Cysts, and Bacteria. This filter provides the best protection against VOC’s, Hydro-Carbon Gas, Cyst and Bacteria Contaminants when used in a Reverse Osmosis Drinking Water System as either a Membrane or Storage Tank Post-filter.

Recommended Service Interval on Most Water Supplies: 3 years

CF1/2MILWFS - Substitute Inline Carbon Post-Filter for Hague Part # 47-211212

The CF1/2MCBWFS (½) .5 micron filter uses Solid Pressed Molded Carbon Block Technology to reduce or remove Cysts, Bacteria, Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, VOC’s, Fine Sediments, Silt, and Clay from untreated water. Small granules of Coconut Shell Carbon are Crushed into Powder, Pressed and Bonded together with a “PATENTED” heat molding process to form a solid BLOCK of Carbon. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The Block Density provides 2-10 times more Volume Weight of Filter Material when compared to other Carbon Filters, also allowing better filtration of the Fine  Sediments, Silt, Clay, Cysts, and Bacteria. This filter provides the best protection against VOC’s, Hydro-Carbon Gas, Cyst and Bacteria Contaminants when used in a Reverse Osmosis Drinking Water System as a Storage Tank Post-filter.

Recommended Service Interval on Most Water Supplies: 3 years

CF1/2MCBWFS - Substitute Carbon Post-Filter for Water Factory Systems Part # 47-211114

The DPF1/2MIMFWFS (1/2) .5 micron filter uses a Graded Density Core, Carbon Impregnated Micro-Fiber Technology to reduce or remove  Dirt, Iron, Sand, Sediment, Silt, Clay, Cysts, Bacteria, Chlorine, Ammonia Chloramines, Hydro-Carbon Gases, and other fine debris from untreated water. Coconut Shell Carbon Powder is impregnated into thousands of small Micro Fibers that are thermally fused together creating a Modified Carbon Block Filter. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The 1/2 micron Fiber Material Density, and Coconut Shell Carbon Powder combination provides 2-3 times more Volume Weight of Filter  Material when compared to other Dual-Purpose Filters. This filter offers the best removal of Chlorine, Hydro-Carbon Gases, Sediments, Silt, Clay, Cysts, and Bacteria when used as a Primary or Secondary Pre-filter for a Reverse Osmosis Drinking Water System.

Recommended Service Interval on Most Water Supplies: 3 years

DPF1/2MIMFWFS - Substitute Sediment/Carbon Pre-Filter for Water Factory Systems Part # 47-1212419 (Must Use With MEM18TFCWFS, MEM30TFCWFS, MEM80TFCWFS TFC Membrane Filter)

The MEM18TFCWFS, MEM30TFCWFS, MEM80TFCWFS .001 micron Membrane filter uses a Thin Film Composite Cellular Skin to separate and remove Dissolved Solids, Salts, Minerals, Heavy Metals, Organic Matter, Pyroxene’s, Sub-micron Colloidal matter, Cysts, Bacteria, and other contaminants from untreated water. Water containing Dissolved Minerals and other Contaminants is forced under high pressure through a Semi-Permeable, Spiral Wound, Thin Film Composite Cellular Skin layered in several wrappings, to separate and rinse away the dissolved solids to a sewage drain, leaving only the Pure, H20 water molecules for consumption, production, processing, or manufacturing. The TFC Membrane skin has a broader PH tolerance, can remove a higher maximum threshold of dissolved solids, and removes a higher percentage of dissolved solids than the CTA Membrane is capable of removing. The TFC Membrane can be used on Municipal or Well Water with proper pre-filtration. Typical Rejection of minerals and impurities for the TFC Membrane is 95%-99% removal, compared to 70%-80% for the CTA Membrane. This is the best Membrane available for Residential Reverse Osmosis Systems.

Recommended Service Interval on Most Water Supplies: 3 years

MEM18TFCWFS, MEM30TFCWFS, MEM80TFCWFS - Substitute Membrane Filter for Water Factory Systems Part # 66-42019, 66-42039, 66-43019, 66-43037, 66-43101 (Must Use With DPF1/2MIMFWFS Sediment/Carbon Pre-Filter)> 12-150 gpd Membranes Available

The CF1/2MCBWFS (½) .5 micron filter uses Solid Pressed Molded Carbon Block Technology to reduce or remove Cysts, Bacteria, Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, VOC’s, Fine Sediments, Silt, and Clay from untreated water. Small granules of Coconut Shell Carbon are Crushed into Powder, Pressed and Bonded together with a “PATENTED” heat molding process to form a solid BLOCK of Carbon. Coconut Shell Carbon has much smaller cell sites in the fractionated carbon granules than Bituminous Coal, offering faster adsorption and more retention capacity of the Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, and VOC’s from the untreated water than Bituminous Coal is capable of. The Block Density provides 2-10 times more Volume Weight of Filter Material when compared to other Carbon Filters, also allowing better filtration of the Fine  Sediments, Silt, Clay, Cysts, and Bacteria. This filter provides the best protection against VOC’s, Hydro-Carbon Gas, Cyst and Bacteria Contaminants when used in a Reverse Osmosis Drinking Water System as a Storage Tank Post-filter.

Recommended Service Interval on Most Water Supplies: 3 years

CF1/2MCBWFS - Substitute Carbon Post-Filter for Water Factory Systems Part # 47-211114

 The SED5MMFWFSQ 5 micron filter uses Conventional Core, Micro-Fiber Technology encapsulated inside of a Proprietary Plastic Housing to remove Dirt, Rocks, Sand, Sticks, Bugs and other larger debris from untreated water. This 5 micron filter is manufactured by thermally fusing thousands of small polypropylene micro fibers together. Smaller particles, Bacteria, and super fine debris such as Silt and Clay pass through this filter because of the inefficient design and larger micron rating. This filter is better suited for Bath, Kitchen, Bar, or Island Sink Faucets and Shower Heads where larger debris plugs the faucet screen, as Pre-Filter for a multistage Reverse Osmosis system, or as a Pre-filter for Spas, Tubs, Tanks, Drums, etc. The Proprietary design restricts the consumer to only one choice of filter cartridge selection and one distribution entity when replacing expired or exhausted filters, which typically imposes a higher retail price and compromise in quality and performance.

Recommended Service Interval on Most Water Supplies: 3 years

SED5MMFWFSQ - Pre-Filter for Water Factory Systems Part # 47-55702-G2

The DPF5MIMFWFSQ 5 micron filter uses Conventional Core, Carbon Impregnated Micro-Fiber Technology encapsulated inside of a Proprietary Plastic Housing to remove Chlorine, Sediment, Sand, and other larger debris from untreated water. Bituminous Coal Powder is impregnated into thousands of small Micro Fibers that are thermally fused together. This “Dual-Purpose” filter has limited success in removing Chlorine and Sediments when used as a Pre-filter for a Reverse Osmosis Drinking Water System due to the inefficient design and larger micron rating. The Proprietary design restricts the consumer to only one choice of filter cartridge selection and one distribution entity when replacing expired or exhausted filters, which typically imposes a higher retail price and compromise in quality and performance.

Recommended Service Interval on Most Water Supplies: 3 years

DPF5MIMFWFSQ - Pre-Filter for Water Factory Systems Part # 47-55706-G2

The MEM18TFCWFSQ (18 gpd), MEM30TFCWFSQ (30 gpd), MEM50TFCWFSQ (50 gpd), MEM80TFCWFSQ (80 gpd) .001 micron Membrane filter uses a Thin Film Composite Cellular Skin encapsulated inside of a Proprietary Plastic Housing to separate and remove Dissolved Solids, Salts, Minerals, Heavy Metals, Organic Matter, Pyroxene’s, Sub-micron Colloidal matter, Cysts, Bacteria, and other contaminants from untreated water. Water containing Dissolved Minerals and other Contaminants is forced under high pressure through a Semi-Permeable, Spiral Wound, Thin Film Composite Cellular Skin layered in several wrappings, to separate and rinse away the dissolved solids to a sewage drain, leaving only the Pure, H20 water molecules for consumption, production, processing, or manufacturing. The TFC Membrane can be used on Municipal or Well Water with proper pre-filtration. The Proprietary design restricts the consumer to only one choice of filter cartridge selection and one distribution entity when replacing expired or exhausted membranes, which typically imposes a higher retail price by forcing the consumer to purchase a Membrane Vessel with Check Valve and Flow Restrictor, in addition to the Membrane Filter with every Membrane replacement. Typical Rejection of minerals and impurities for the TFC Membrane is 95%-99% removal, compared to 70%-80% for the CTA Membrane.

Recommended Service Interval on Most Water Supplies: 3 years

MEM18TFCWFSQ (18 gpd), MEM30TFCWFSQ (30 gpd), MEM50TFCWFSQ (50 gpd), MEM80TFCWFSQ (80 gpd) - Membrane Filter for Water Factory Systems Part # 66-4703-G2, 66-4706-G2, 66-4507-G2, 66-4709-G2 > 18-150 gpd Membranes available.

The CF10MCBWFSQ 10 micron filter uses Extruded Carbon Block Technology encapsulated inside of a Proprietary Plastic Housing to reduce or remove Chlorine, Hydro-Carbon Gases, Sediments and other debris from untreated water. Small granules of Bituminous Carbon are crushed and molded into long solid Blocks of Carbon and then cut to specific lengths. Ammonia, Chloramines, VOC’s, Sediment, Silt, Clay, and Bacteria pass through this filter because of the Carbon used and larger micron rating. This filter provides reasonable protection against Chlorine and Hydro-Carbon Gas contaminants, and is better suited for Bath, Kitchen, Bar, or Island Sink Faucets and Shower Heads, as a Pre-Filter for a multistage Reverse Osmosis system, or as a Pre-filter for Tubs, Tanks, Pitchers, etc. This filter utilizes a Proprietary design which restricts the consumer to only one choice of filter cartridge selection and one distribution entity when replacing expired or exhausted filters, which typically imposes a higher retail price and compromise in quality and performance.

Recommended Service Interval on Most Water Supplies: 3 years

CF10MCBWFSQ Substitute Carbon Post-Filter for Water Factory Systems Part # 47-55710-G2

The SED5MMFWFSQ 5 micron filter uses Conventional Core, Micro-Fiber Technology encapsulated inside of a Proprietary Plastic Housing to remove Dirt, Rocks, Sand, Sticks, Bugs and other larger debris from untreated water. This 5 micron filter is manufactured by thermally fusing thousands of small polypropylene micro fibers together. Smaller particles, Bacteria, and super fine debris such as Silt and Clay pass through this filter because of the inefficient design and larger micron rating. This filter is better suited for Bath, Kitchen, Bar, or Island Sink Faucets and Shower Heads where larger debris plugs the faucet screen, as Pre-Filter for a multistage Reverse Osmosis system, or as a Pre-filter for Spas, Tubs, Tanks, Drums, etc. The Proprietary design restricts the consumer to only one choice of filter cartridge selection and one distribution entity when replacing expired or exhausted filters, which typically imposes a higher retail price and compromise in quality and performance.

Recommended Service Interval on Most Water Supplies: 3 years

SED5MMFWFSQ - Pre-Filter for Water Factory Systems Part # 47-55702-G2

The MEM18CTAWFSQ .005 micron Membrane filter uses a Cellulose Tri-Acetate Cellular Skin encapsulated inside of a Proprietary Plastic Housing to separate and remove Dissolved Solids, Salts, Minerals, Heavy Metals, Organic Matter, Sub-micron Colloidal matter, Cysts, Bacteria, and other contaminants from untreated water. Water containing Dissolved Minerals and other Contaminants is forced under high pressure through a Semi-Permeable, Spiral Wound, Cellulose Tri-Acetate Cellular Skin layered in several wrappings, to separate and rinse away many of the dissolved solids to a sewage drain. The CTA Membrane can only operate on Chlorinated water supplies, excluding it from use on Private, Shared, or Municipal Well Water which could possibly contain Bacteria that would contaminate and foul the CTA skin. The CTA Membrane is not capable of removing the maximum level of dissolved solids as the TFC Membrane, does not have the broad PH range flexibility as the TFC Membrane, and does not remove the percentage of dissolved solids that the TFC Membrane is capable of removing. Typical Rejection of minerals and impurities for the CTA Membrane is 70%-80% removal, compared to 95%-99% of the TFC Membrane. The Proprietary design restricts the consumer to only one choice of filter cartridge selection and one distribution entity when replacing expired or exhausted membranes, which typically imposes a higher retail price by forcing the consumer to purchase a Membrane Vessel with Check Valve and Flow Restrictor, in addition to the Membrane Filter with every Membrane replacement.

Recommended Service Interval on Most Water Supplies: 3 years

MEM18CTAWFSQ - Membrane Filter for Water Factory Systems Part # 66-4603-G2 > 18-150 gpd Membranes available.

The CF10MCBWFSQ 10 micron filter uses Extruded Carbon Block Technology encapsulated inside of a Proprietary Plastic Housing to reduce or remove Chlorine, Hydro-Carbon Gases, Sediments and other debris from untreated water. Small granules of Bituminous Carbon are crushed and molded into long solid Blocks of Carbon and then cut to specific lengths. Ammonia, Chloramines, VOC’s, Sediment, Silt, Clay, and Bacteria pass through this filter because of the Carbon used and larger micron rating. This filter provides reasonable protection against Chlorine and Hydro-Carbon Gas contaminants, and is better suited for Bath, Kitchen, Bar, or Island Sink Faucets and Shower Heads, as a Pre-Filter for a multistage Reverse Osmosis system, or as a Pre-filter for Tubs, Tanks, Pitchers, etc. This filter utilizes a Proprietary design which restricts the consumer to only one choice of filter cartridge selection and one distribution entity when replacing expired or exhausted filters, which typically imposes a higher retail price and compromise in quality and performance.

Recommended Service Interval on Most Water Supplies: 3 years

CF10MCBWFSQ - Substitute Carbon Post-Filter for Water Factory Systems Part # 47-55710-G2

The CF100MGACWFSCM 100 micron filter uses Granular Carbon Technology encapsulated inside of a Proprietary Plastic Housing to remove Chlorine and other Hydro-Carbon Gases from untreated water. Small Granules of Bituminous Carbon are encapsulated in a Plastic container along with a very small micro-fiber pre-filter element. The inefficient design and larger micron rating lets all Sediments, Sand, Bacteria, and Debris pass through the cartridge, while only removing Chlorine and other Hydro-Carbon Gases in limited amounts. This filter is better suited for Bath, Shower, or Utility Sink type Faucets, or as a Pre-filter for Spas, Tubs, Tanks, Drums, Feeders, etc. where higher flow rates of water are required. The Proprietary design restricts the consumer to only one choice of filter cartridge selection and one distribution entity when replacing expired or exhausted filters, which typically imposes a higher retail price and compromise in quality and performance.

Recommended Service Interval on Most Water Supplies: 3 years

CF100MGACWFSCM - Substitute Granular Carbon Filter for Water Factory Systems Part # 47-55704-G2

The CF1MCBWFSCM 1 micron filter uses Solid Pressed Molded Carbon Block Technology encapsulated inside of a Proprietary Plastic Housing to reduce or remove Cysts, Bacteria, Chlorine, Ammonia, Chloramines, Hydro-Carbon Gases, VOC’s, Fine Sediments, Silt, and Clay from untreated water. Small granules of Coconut Shell Carbon are Crushed into Powder, Pressed and Bonded together with a “PATENED” heat molding process to form a solid BLOCK of Carbon. The Block Density provides 2-10 times more Volume Weight of Filter Material when compared to other Carbon Filters. This filter provides next to the best protection against VOC’s, Hydro-Carbon Gases, Silt, Clay, Cyst and Bacteria Contaminants when used in Reverse Osmosis Systems, Beverage Dispensers, Ice Machines, Coffee Machines, Distillers, Fountains, Refrigerators, and other appliances. This filter utilizes a Proprietary design which restricts the consumer to only one choice of filter cartridge selection and one distribution entity when replacing expired or exhausted filters, which typically imposes a higher retail price and compromise in quality and performance.

Recommended Service Interval on Most Water Supplies: 3 years

CF1MCBWFSCM - Substitute Ultrafine Carbon Block Filter for Water Factory Systems Part # 47-55707-G2

The CF5MCBWFSCM 5 micron filter uses Extruded Carbon Block Technology encapsulated inside of a Proprietary Plastic Housing to reduce or remove Chlorine, Hydro-Carbon Gases, Sediments and other debris from untreated water. Small granules of Bituminous Carbon are crushed and molded into long solid Blocks of Carbon and then cut to specific lengths. Ammonia, Chloramines, VOC’s, Sediment, Silt, Clay, and Bacteria pass through this filter because of the Carbon used and larger micron rating. This filter provides reasonable protection against Chlorine and Hydro-Carbon Gas contaminants, and is better suited for Bath, Kitchen, Bar, or Island Sink Faucets and Shower Heads, as a Pre-Filter for a multistage Reverse Osmosis system, or as a Pre-filter for Tubs, Tanks, Pitchers, etc. This filter utilizes a Proprietary design which restricts the consumer to only one choice of filter cartridge selection and one distribution entity when replacing expired or exhausted filters, which typically imposes a higher retail price and compromise in quality and performance.

Recommended Service Interval on Most Water Supplies: 3 years

CF5MCBWFSCM - Substitute 5 micron Carbon Block Filter for Water Factory Systems Part # 47-55708-G2

The DPF5MIMFLWFSCM 5 micron filter uses Conventional Core, Carbon Impregnated Micro-Fiber Technology, and an Ion exchange media that is specific to soluable lead, all encapsulated inside of a Proprietary Plastic Housing to reduce or remove Chlorine, Sediment, Sand, Lead and other debris from untreated water. Bituminous Coal Powder and an Ion exchange media is impregnated into thousands of small Micro Fibers that are thermally fused together. This “Dual-Purpose” filter has limited success in removing Chlorine and Sediments when used as a Pre-filter for a Reverse Osmosis Drinking Water System due to the inefficient design and larger micron rating. The Proprietary design restricts the consumer to only one choice of filter cartridge selection and one distribution entity when replacing expired or exhausted filters, which typically imposes a higher retail price and compromise in quality and performance.

Recommended Service Interval on Most Water Supplies: 3 years

DPF5MIMFLWFSCM - Substitute Sediment and Lead reduction Filter for Water Factory Systems Part # 47-55711-G2

The DPF5MIMFLSWFSCM 5 micron filter uses Conventional Core, Carbon Impregnated Micro-Fiber Technology, an Ion exchange media that is specific to soluable lead, and a Phosphate for Hard Water Scale control, all encapsulated inside of a Proprietary Plastic Housing to reduce or remove Chlorine, Sediment, Sand, Lead, Hard Water Deposits and other debris from untreated water. Bituminous Coal Powder and an Ion exchange media is impregnated into thousands of small Micro Fibers that are thermally fused together, along with the addition of Phosphate Crystals. This “Three-Purpose” filter has limited success in removing Chlorine and Sediments when used as a Pre-filter for a Reverse Osmosis Drinking Water System due to the inefficient design and larger micron rating. The Proprietary design restricts the consumer to only one choice of filter cartridge selection and one distribution entity when replacing expired or exhausted filters, which typically imposes a higher retail price and compromise in quality and performance.

Recommended Service Interval on Most Water Supplies: 3 years

DPF5MIMFLSWFSCM - Substitute Sediment, Lead, and Scale reduction Filter for Water Factory Systems Part # 47-55713-G2